View SXX06DSY_1169627.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

217 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx06xsx & sxx06x series 6 amp sensitive & standard scrs 6.0a scrs sxx06xsx & sxx06x series description excellent unidirectional switches for phase control applications such as heating and motor speed controls. sensitive gate scrs are easily triggered with microamps of current as furnished by sense coils, proximity switches, and microprocessors. standard phase control scrs are triggered with few milliamperes of current at less than 1.5v potential. features & bene?ts t 3p)4dpnqmjbou t (mbttoqbttjwbufe junctions t 7pmubhfdbqbcjmjuzvq to 1000 v t 4vshfdbqbcjmjuzvqup 100 a main features symbol value unit i t(rms) 6a v drm /v rrm 400 to 1000 v i (5 0.2 to 15 ma schematic symbol agency approval agency agency file number ? l package: e71639 applications typical applications are capacitive discharge systems for strobe lights, nailers, staplers and gas engine ignition. also controls for power tools, home/brown goods and white goods appliances. internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. ? ak g
218 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 6 amp sensitive & standard scrs sxx06xsx & sxx06x series absolute maximum ratings standard scrs symbol parameter value unit i t(rms) rms on-state current sxx06l t c = 100c 6a sxx06r sxx06d sxx06v t c = 110c i t(av) average on-state current sxx06l t c = 100c 3.8 a sxx06r sxx06d sxx06v t c = 110c i tsm peak non-repetitive surge current tjohmfibmgdzdmfg)[ t j (initial) = 25c 83 a tjohmfibmgdzdmfg)[ t j (initial) = 25c 100 i 2 ti 2 t value for fusing t p = 8.3 ms 41 a 2 s di/dt critical rate-of-rise of on-state current g)[5 j =125c 100 a/s i (5. peak gate current t j = 125c 2a p ( "7
average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c note: xx = voltage absolute maximum ratings sensitive scrs symbol parameter test conditions value unit i t(rms) rms on-state current sxx06lsy t c = 80c 6a sxx06rsy SXX06DSY sxx06vsy t c = 95c i t(av) average on-state current sxx06lsy t c = 80c 3.8 a sxx06rsy SXX06DSY sxx06vsy tc = 95c i tsm peak non-repetitive surge current tjohmfibmgdzdmfg)[ t j (initial) = 25c 83 a tjohmfibmgdzdmfg)[ t j (initial) = 25c 100 i 2 ti 2 t value for fusing t p = 8.3 ms 41 a 2 s di/dt critical rate of rise of on-state current g)[5 j = 110c 100 a/s i (5. peak gate current t j = 110c 1a p ( "7
average gate power dissipation t j = 110c 0.1 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 110 c note: xx = voltage, y = sensitivity
219 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx06xsx & sxx06x series 6 amp sensitive & standard scrs 6.0a scrs electrical characteristics (t j = 25c, unless otherwise speci?ed) sensitive scrs symbol test conditions value unit sxx06xs2 sxx06xs3 i (5 v d = 6v r l = 100 8 max. 200 500 a v (5 max. 0.8 v dv/dt v d = v drm ; r (, = 1k; t j = 110c typ. 8 v/s v (% v d = v drm r l = 3.3 k 8 t j = 110c min. 0.2 v v (3. i (3 = 10a min. 6 v i ) i t = 20ma (initial) max. 6 8 ma t q i t = 2a; t p = 50s; dv/dt=5v/s; di/dt=-30a/s max. 50 45 s t gt i ( = 2 x i (5 pw = 15s i t = 12a typ. 4 5 s note: xx = voltage, x = package electrical characteristics (t j = 25c, unless otherwise speci?ed) standard scrs symbol test conditions value unit sxx06x i (5 v d = 12v r l = 60 8 max. 15 ma v (5 max. 1.5 v dv/dt v d = v drm ; gate open; t j = 100c 400v min. 350 v/s 600v 300 800v 250 1000v 100 v d = v drm ; gate open; t j = 125c 400v 250 600v 225 800v 200 v (% v d = v drm r l = 3.3 k 8 t j = 125c min. 0.2 v i ) i t = 200ma (initial) max. 30 ma t q i t = 2a; t p = 50s; dv/dt=5v/s; di/dt=-30a/s max. 35 s t gt i ( = 2 x i (5 pw = 15s i t = 12a typ. 2 s note: xx = voltage, x = package
220 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 6 amp sensitive & standard scrs sxx06xsx & sxx06x series static characteristics symbol test conditions value unit v tm i t = 12a; t p = 380 s max. 1.6 v i drm / i rrm v drm = v rrm sxx06xyy t j = 25c o7 max. 5 a t j = 110c o7 250 sxx06x t j = 25c o7 10 1000v 20 t j = 100c o7 200 1000v 3000 t j = 125c o7 500 note: xx = voltage, x = package, yy = sensitivity thermal resistances symbol parameter value unit r r (j-c) junction to case (ac) sxx06rsy 2.6 c/w sxx06lsy 4.3 sxx06vsy 2.4 SXX06DSY 1.8 sxx06r 2.5 sxx06l 4.0 sxx06v 2.3 sxx06d 1.7 r r (j-a) junction to ambient sxx06rsy 40 c/w sxx06lsy 65 sxx06vsy 85 sxx06r 40 sxx06l 50 sxx06v 70 note: xx = voltage, y = sensitivity
221 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx06xsx & sxx06x series 6 amp sensitive & standard scrs 6.0a scrs figure 1: normalized dc gate trigger current vs. junction temperature (sensitive scr) figure 2: normalized dc gate trigger current vs. junction temperature (standard scr) 0.0 1. 0 2.0 3.0 4.0 junction temperature (t j ) - (oc) ratio of i gt /i gt (t j =2 5 oc) -4 -15 10 35 60 85 110 0.0 1.0 2.0 3.0 4.0 junction temperature (t j ) - (oc) ratio of i gt / i gt (t j = 2 5 oc) -40 -15 10 35 60 85 110 125 figure 5: on-state current vs. on-state voltage (typical) figure 6: power dissipation (typical) vs. rms on-state current 0 1 2 3 4 5 6 0 1 2 3 4 5 6 rms on-state current [i t(rms) ] - (amps) average on-state power dissipation [p d(av) ] - (watts) 0.0 0.5 1.0 1.5 2.0 junction temperature (t j ) - (oc) ratio of v gt / v gt (t j = 2 5 oc) -40 -15 10 35 60 85 110 125 figure 3: normalized dc gate trigger voltage vs. junction temperature figure 4: normalized dc holding current vs. junction temperature 0.0 0.5 1.0 1.5 2.0 junction temperature (t j ) - (oc) ratio of i h / i h (t j = 2 5 oc) -40 -15 10 35 60 85 110 125 5 instantaneous on-state current (i t ) -amps 0 10 15 20 25 30 t j = 2 5 c 0.7 0.8 0.9 instantaneous on-state voltage (v t ) - volts 1.0 1.1 1.2 1.3 1.4 1.5 1.6
222 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 6 amp sensitive & standard scrs sxx06xsx & sxx06x series figure 7: maximum allowable case temperature vs. rms on-state current figure 8: maximum allowable case temperature vs. average on-state current 80 85 90 95 100 105 110 11 5 120 125 130 4 3 2 1 0 sxx06l sx06lsy sxx06rsy SXX06DSY sxx06vsy sxx06r sxx06d sxx06v current waveform: sinsuoidal load: resistive or inductive conduction angle: 180 free air rating average on-state current [i t(ave) ] - amps maximum allowable case temperature (t c ) - oc 80 85 90 95 100 105 110 115 120 125 130 sxx06r sxx06d sxx06v 0 1 2 3 4 5 6 7 current waveform: sinsuoidal load: resistive or inductive conduction angle: 180 free air rating sxx06l rms on-state current [i t(rms) ] - amps maximum allowable case temperature (t c ) - o c sxx06lsy sxx06rsy SXX06DSY figure 9: maximum allowable ambient temperature vs. rms on-state current 0 20 40 60 80 100 120 0.0 0.5 1.0 1.5 2.0 2.5 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating sxx06v sxx06rsy sxx06lsy sxx06vsy sxx06l sxx06r rms on-state current [i t(rms) ] - amps maximum allowable temperature (t a ) - oc figure 10: maximum allowable ambient temperature vs. average on-state current 0 20 40 60 80 100 120 5 . 1 0 . 1 5 . 0 0 . 0 current waveform: sinusoidal load: resistive or inductive conduction angle: 180 free air rating sxx06rsy sxx06lsy sxx06r sxx06l sxx06v sxx06vsy average on-state current [i t(ave) ] - amps maximum allowable ambient temperature (t a ) - oc note: xx = voltage, y = sensitivity figure 11: peak capacitor discharge current 10 100 1000 0 . 0 5 0 . 5 2 0 . 5 5 . 0 pulse current duration (t w ) - ms peak discharge current (i tm ) - amps i trm t w figure 12: peak capacitor discharge current derating 0.0 0.2 0.4 0.6 0.8 1. 0 1. 2 0 2 5 50 75 100 125 150 normalized peak current sensitive scr case temperature (t c ) - oc standard scr
223 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx06xsx & sxx06x series 6 amp sensitive & standard scrs 6.0a scrs 1 10 100 surge current duration -- full cycles peak surge (non-repetitive) on-state current (i tsm ) C amps 1 10 100 1000 figure 13: surge peak on-state current vs. number of cycles 4611-:'3&26&/$:)[4jovtpjebm load: resistive rms on-state current: [i t(rms) ]: maximum rated value at speci?ed case temperature notes: (bufdpouspmnbzcfmptuevsjohboejnnfejbufmz following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value. soldering parameters re?ow condition 1co'sffbttfncmz pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) otfdt average ramp up rate (liquidus temp) (t l ) to peak 5c/second max t s(max) to t l - ramp-up rate 5c/second max re?ow - temperature (t l ) (liquidus) 217c - temperature (t l ) otfdpoet peak temperature (t p ) 260 +0/-5 c time within 5 c of actual peak temperature (t p ) otfdpoet ramp-down rate 5c/second max time 2 5 c to peak temperature (t p ) 8 minutes max. do not exceed 280c time temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p reheat ramp-up ramp-up ramp-down r am p - do
224 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 6 amp sensitive & standard scrs sxx06xsx & sxx06x series physical speci?cations environmental speci?cations test speci?cations and conditions ac blocking mil-std-750, m-1040, cond a applied peak ac voltage @ 125c for 1008 hours temperature cycling mil-std-750, m-1051, 100 cycles; -40c to +150c; 15-min dwell-time temperature/ humidity eia / jedec, jesd22-a101 1008 hours; 320v - dc: 85c; 85% rel humidity high temp storage mil-std-750, m-1031, 1008 hours; 150c low-temp storage 1008 hours; -40c thermal shock mil-std-750, m-1056 10 cycles; 0c to 100c; 5-min dwell- time at each temperature; 10 sec (max) transfer time between temperature autoclave eia / jedec, jesd22-a102 168 hours (121c at 2 atms) and 3) resistance to solder heat mil-std-750 method 2031 solderability ansi/j-std-002, category 3, test a lead bend mil-std-750, m-2036 cond e terminal finish 100% matte tin-plated body material 6-sfdphoj[fefqpyznffujohnbnnbcjmjuz classi?cation 94v-0 lead material copper alloy design considerations careful selection of the correct device for the applications operating parameters and environment will go a long way upxbsefyufoejohuifpqfsbujohmjgfpguif5izsjtups(ppe design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. correct mounting, soldering, and forming of the leads also help protect against component damage. product selector part number voltage gate sensitivity type package 400v 600v 800v 1000v sxx06rs2 x x 0.2ma sensitive scr to-220r sxx06ls2 x x 0.2ma sensitive scr to-220l sxx06vs2 x x 0.2ma sensitive scr to-251 sxx06ds2 x x 0.2ma sensitive scr to-252 sxx06rs3 x x 0.5ma sensitive scr to-220r sxx06ls3 x x 0.5ma sensitive scr to-220l sxx06vs3 x x 0.5ma sensitive scr to-251 sxx06ds3 x x 0.5ma sensitive scr to-252 sxx06r xxxx 15ma st andard scr to-220r sxx06l xxxx 15ma st andard scr to-220l sxx06v xxxx 15ma st andard scr to-251 sxx06d xxxx 15ma st andard scr to-252 note: xx = voltage
225 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx06xsx & sxx06x series 6 amp sensitive & standard scrs 6.0a scrs dimensions to-251aa (v/i-package) v/i-pak through hole dimension inches millimeters min typ max min typ max a 0.040 0.044 0.050 1.02 1.11 1.27 b 0.235 0.242 0.245 5.97 6.15 6.22 c 0.350 0.361 0.375 8.89 9.18 9.53 d 0.205 0.208 0.213 5.21 5.29 5.41 e 0.255 0.262 0.265 6.48 6.66 6.73 f 0.027 0.031 0.033 0.69 0.80 0.84 ( 0.087 0.090 0.093 2.21 2.28 2.36 ) 0.085 0.092 0.095 2.16 2.34 2.41 i 0.176 0.180 0.184 4.47 4.57 4.67 j 0.018 0.020 0.023 0.46 0.51 0.58 , 0.038 0.040 0.044 0.97 1.01 1.12 l 0.018 0.020 0.023 0.46 0.52 0.58 p 0.042 0.047 0.052 1.06 1.20 1.32 q 0.034 0.039 0.044 0.86 1.00 1.11 r 0.034 0.039 0.044 0.86 1.00 1.11 s 0.074 0.079 0.084 1.86 2.00 2.11 area: 0.040 in 2 t c measuring point gate g i e d a b c f j h k l 5.28 .208 5.34 .210 anode cathode anode p q r s dimensions to-252aa (d-package) d-pak surface mount dimension inches millimeters min typ max min typ max a 0.040 0.043 0.050 1.02 1.09 1.27 b 0.235 0.243 0.245 5.97 6.16 6.22 c 0.106 0.108 0.113 2.69 2.74 2.87 d 0.205 0.208 0.213 5.21 5.29 5.41 e 0.255 0.262 0.265 6.48 6.65 6.73 f 0.027 0.031 0.033 0.69 0.80 0.84 ( 0.087 0.090 0.093 2.21 2.28 2.36 ) 0.085 0.092 0.095 2.16 2.33 2.41 i 0.176 0.179 0.184 4.47 4.55 4.67 j 0.018 0.020 0.023 0.46 0.51 0.58 , 0.038 0.040 0.044 0.97 1.02 1.12 l 0.018 0.020 0.023 0.46 0.51 0.58 m 0.000 0.000 0.004 0.00 0.00 0.10 n 0.021 0.026 0.027 0.53 0.67 0.69 o 005005 p 0.042 0.047 0.052 1.06 1.20 1.32 q 0.034 0.039 0.044 0.86 1.00 1.11 m o n h j l k .118 3 .063 1.60 .071 1.80 .264 6.71 .264 6.71 .181 4.60 gate anode cathode anode t c measuring point g i d e a b c f 5.28 .208 5.34 .210 : 0.040 in 2 area p q
226 revised: july 29, 2010 09:54 am ?2010 littelfuse, inc teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 6 amp sensitive & standard scrs sxx06xsx & sxx06x series dimensions to-220ab (r-package) non-isolated mounting tab common with center lead dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 ( 0.540 0.575 13.72 14.61 ) 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 , 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.52 r 0.038 0.048 0.97 1.22 k j a h g b f e c d l r t c measuring point anode o p n m .276 7. 0 1 .526 13.36 .320 8.13 area (ref.) 0.17 in 2 notch in gate lead to id. non-isolated tab gate cathode anode dimensions to-220ab (l-package) isolated mounting tab dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 ( 0.540 0.575 13.72 14.61 ) 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 , 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.52 r 0.038 0.048 0.97 1.22 a h g b f e c d l r t c measuring point area (ref.) 0.17 in 2 o p n m .320 8.13 .526 13.36 .276 7. 0 1 k j gate cathode anode note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm).
227 ?2010 littelfuse, inc revised: july 29, 2010 09:54 am teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. sxx06xsx & sxx06x series 6 amp sensitive & standard scrs 6.0a scrs packing options part number marking weight packing mode base quantity sxx06l/ryy sxx06l/ryy 2.2 g bulk 500 sxx06l/ryytp sxx06l/ryy 2.2 g tube 500 (50 per tube) sxx06dyytp sxx06dyy 0.3 g tube 750 (75 per tube) sxx06dyyrp sxx06dyy 0.3 g embossed carrier 2500 sxx06vyytp sxx06vyy 0.4 g tube 750 (75 per tube) sxx06l/r sxx06l/r 2.2 g bulk 500 sxx06l/rtp sxx06l/r 2.2 g tube 500 (50 per tube) sxx06dtp sxx06d 0.3 g tube 750 (75 per tube) sxx06drp sxx06d 0.3 g embossed carrier 2500 sxx06vtp sxx06v 0.4 g tube 750 (75 per tube) note: xx = voltage; yy = sensitivity 0.512 (13.0) arbor hole diameter dc xxxxxx xxxxxx dc xxxxxx dc xxxxxx xx gate cathode anode 0.63 (16.0) 0.157 (4.0) 0.64 (16.3) 12.99 (330.0) 0.524 (13.3) 0.315 (8.0) 0.059 dia (1.5) * * cover tape xx xx direction of feed dimensions are in inches (and millimeters). to-252 embossed carrier reel pack (rp) specs meets all eia-481-2 standards part numbering system part marking system s 60 06 l s2 56 device type s: scr voltage rating 40: 400v 60: 600v 80: 800v k0: 1000v current rating 06: 6a sensitivity & type sensitive scr: s2: 200a s3: 500a standard scr: (blank): 15ma package type l: to-220 isolated r: to-220 non-isolated v: to-251 (v/i-pak) d: to-252 (d-pak) lead form dimensions xx: lead form option to-252aa C (d package) to-251aa C (v package) s6006ds2 yxxxx ? yxxxx s6006rs2 to-220ab (r and l packages) ?

▲Up To Search▲

Price & Availability of SXX06DSY

	To Download SXX06DSY Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .